- [UAPG2/G3] Enable VHT40/80 support for Japan.
- [UAPG2/G3] Switch to LEDE framework.
- [UAPG2/G3] Implement upgraded authenticator.
- [UAPG2/G3] Fix Fast Roaming support.
- [UAPG2/G3] Fix Cell Size Tuning support.
- [UAPG3] Fix BLE support.
- [UAPG3] Fix a node leak.
- [UAPG3] Fix a bug where the AP may wrongly kick a client STA when "on other VAP" occurs.
- [UAPG3] Fix a bug in uplink that would cause the downlink to hang after a channel change.
- [UAPG3] Fix inter-VLAN communication issue (reported HERE).
- [UAPG3] Fix and improve wireless uplink support.
- [UAPG3] Fix a bug which may cause RF scanning to return incorrect results.
- [UAPG2] Fix a bug where the downlink will be disconnected when the uplink AP changes channels.
- [HD/SHD/XG/BaseStationXG] Fix and improve Hotspot 2.0 support.
- [SHD/XG/BaseStationXG] Enable Rogue AP scanning on the security radio.
- [XG/BaseStationXG] Fix reported 10Gbps PHY rate (requires 5.9.29+).
- [BaseStationXG] Enable LED bar and OLED display support.
- [nanoHD/IW-HD] Add client `Framed-IP-Address` to RADIUS accounting data.
- [nanoHD/IW-HD] Improve 802.11k scanning.
- [nanoHD/IW-HD] Improve Ethernet stability.
- [nanoHD/IW-HD] Improve Fast Roaming support.
- [nanoHD/IW-HD] Fix a bug which may make bandsteering fail to initialize.
- [nanoHD/IW-HD] Fix instability caused by enabling WLAN scheduling.
- [nanoHD/IW-HD] Fix throughput issue for clients with certain Intel wireless cards.
- [nanoHD/IW-HD] Fix wireless adoption issue.
- [nanoHD/IW-HD] Fix a memory leak.
- [nanoHD/IW-HD] Fix multiple downlink support.
- [nanoHD/IW-HD] Fix wrong passphrase issue that some client STAs encountered.
- [nanoHD/IW-HD] Fix mDNS packets being dropped by IGMP snooping.
- [nanoHD/IW-HD] Fix bandsteering support when WLAN scheduling enabled.
- [nanoHD/IW-HD] Fix a bug causing instability when netconsole was enabled.
- [nanoHD/IW-HD] Fix a bug which may cause some SSID(s) not to broadcast.
- [nanoHD/IW-HD] Fix a bug in bandsteering.
- [nanoHD/IW-HD] Fix an issue with wireless adoption when in factory default state.
- [nanoHD/IW-HD] Fix wireless uplink VLAN broadcast/multicast packets format error issue.
- [nanoHD/IW-HD] Fix SSDP dropped by IGMP snooping issue.
- [nanoHD/IW-HD] Fix a bug causing a drop in transmit performance.
- [nanoHD/IW-HD] Fix RF scanning support.
- [nanoHD/IW-HD] Fix support for 8 SSIDs per radio.
- [nanoHD/IW-HD] Fix a bug which may cause an AP to stop forwarding packets when configured to use wireless uplink.
- [nanoHD/IW-HD] Fix a bug when using VLANs in a wireless uplink topology.
- [nanoHD/IW-HD] Stability improvements.
- [IW-HD] Add wired RADIUS MAC auth & DVLAN support.
- [IW-HD] Add wired 802.1X fallback VLAN support.
- [IW-HD] Add support to control PoE passthrough.
- [IW-HD] Enable cell size tuning support.
- [IW-HD] Fix 802.1X auto mode.
- [IW-HD] Fix a bug in wired 802.1X support.
- [IW-HD] Fix wireless uplink support while in factory default state.
- [EDU] Use new package manager for EDU SIP.
- [UAP] Enable fast-apply support for minRSSI.
- [UAP] Silence unnecessary LLDP log spam.
- [UAP] Fix false MAC filter rejection anomalies in the controller.
- [UAP] Improve wireless uplink loop detection to fix disconnect issues.
- [USW] Add more DHCP snooping statistics to CLI output.
- [USW] Increase local syslog size.
- [USW] Forward IGMP report packets only on ports with LLDP remote entry.
- [USW] Forward keepalive (L2 multicast) on IGMP enabled switch.
- [USW] Fix a bug causing issues with DHCP in some environments.
- [USXG6POE] Improve PD compatibility.
- [HW] Fix DHCP option 43 support.
- [HW] Fix false `Decrypt Error` events and improve logging.
- [HW] Security improvement.
- [HW] Miscellaneous bug fixes and improvements.
If you update the Access Point (AP) firmware, your device can benefit from changes that fix multiple issues encountered by wireless clients, correct different user interface problems, add various functionalities, and include support for newly developed protocols.
Before performing this task, we recommend that you read and understand all the installation steps, because there are many AP models and manufacturers available. Each producer strives to make the procedure as simple as possible, but there are cases when it's anything but that.
It is also advisable that you apply a new access point firmware in a steady power environment (UPS unit will satisfy this need), using an Ethernet cable rather than a wireless connection. The latter can be easily interrupted.
With this in mind, if you wish to apply this version, click the download button and install the package on your access point. Remember to check back with our website as often as possible so that you don't miss a single new release.
Top 4 Download periodically updates information of Ubiquiti UAP v2 Access Point Firmware 4.0.9.9636 full driver from the manufacturer, but some information may be slightly out-of-date.
Using warez version of Ubiquiti UAP v2 Access Point Firmware 4.0.9.9636 driver is hazardous. Our driver download links are directly from our mirrors or publisher's website, Ubiquiti UAP v2 Access Point Firmware 4.0.9.9636 torrent files or shared files from free file sharing and free upload services, including Rapidshare, HellShare, HotFile, FileServe, MegaUpload, YouSendIt, MailBigFile, DropSend, MediaMax, zUpload, MyOtherDrive, SendSpace, DepositFiles, Letitbit, LeapFile, DivShare or MediaFire, are not allowed!
It is not recommended to download drivers from illegal sites which distribute a keygens, key generators, pirate keys, serial numbers, warez full versions or cracks for Ubiquiti UAP v2 Access Point Firmware 4.0.9.9636. These drivers might corrupt your computer installation or breach your privacy. A driver might contain a trojan horse opening a backdoor on your computer. Hackers can use this backdoor to take control of your computer, copy data from your computer or to use your computer to distribute viruses and spam to other people.
Download Now
Update All Drivers