Peplink Pepwave Surf SOHO MK3 HW1 Router Firmware 7.1.2

Feature Improvements:

- [Front Panel] Added an option to view the hardware revision from Front Panel Display.
Compatible with Balance: 305, 380 or above
Compatible with MediaFast: 500/750

- [InControl] Added option to disable InControl 2 configuration management.
Compatible with All Balance / MAX / Surf models

Resolved Issues:

- [AP Controller] RADIUS MAC Authentication does not work in Open/WPA-PSK modes.
Compatible with Balance: 305, 380 or above
Compatible with MediaFast: 500/750

- [AP] If the VLAN ID is set in SSID, the unit may experience system instability.
Compatible with Balance: One
Compatible with MAX: 700, OTG, BR1, BR1 MK2, BR1 Mini, BR1 IP55/IP67, BR2, Hotspot, Transit, HD2/HD4 series
Compatible with MediaFast: 200, HD2, HD4
Compatible with Surf: SOHO, SOHO MK3

- [Captive Portal] After clicking "Start Browsing", the portal may fall into a redirection loop.
Compatible with All Balance / MAX / MediaFast models (Excludes MAX OTG)

- [GPS] GPX files doe not contain GPS information.
Compatible with MAX: BR1, BR1 Slim, BR1 Mini, BR1 ENT, Transit, HD2/HD4 series
Compatible with MediaFast: HD2, HD4

- [IPsec] DH group 19/20/21 does not work.
Compatible with Balance: One
Compatible with MAX: BR1 MK2, Hotspot, Transit, HD2/HD4 series
Compatible with MediaFast: 200, HD2, HD4

- [Routing] Packets forwarded to WAN from LAN incorrectly.
Compatible with Surf: SOHO MK3

- [LAN] The Built-in WINS Server may cause system instability.
- [LAN] Cannot obtain an IP address via DHCP if the LAN Port set as Access Mode with VLAN.
- [LAN] Subnet mask of additional IP Addresses have been used on the primary LAN network.
- [NAT Mapping] LAN NAT does not work across different VLAN.
- [Outbound Policy] After tunnel failback, the VPN sub-tunnel reply traffic may not be routed on proper sub-tunnel.
- [Outbound Policy] Traffic may be routed to the wrong PepVPN sub-tunnel.
- [PepVPN] Disabling a tunnel in the PepVPN test may trigger it into cold failover standby.
- [PepVPN] Event Log shows unsupported version incorrectly.
- [PepVPN] Multiple tunnel is not compatible with NAT mode.
- [PepVPN] OSPF running on Layer 2 PepVPN.
- [PepVPN] Route Conflict will be shown if OSPF custom interface is configured
- [PepVPN] SpeedFusion may use the removed profile incorrectly.
- [PepVPN] If a sub-tunnel is unable to connect, any additional Sub-tunnels will also be unable to connect.
- [Routing] Packets were forwarded to WAN from LAN incorrectly
Compatible with All Balance / MAX / Surf models

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn't either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn't be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don't always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you're looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don't power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don't miss the update that will improve your device.