- PDAF (Phase Detection Auto Focus) functionality has been added. Employing a method of combining image plane phase-difference detection AF and contrast AF.
- Focus Guide function has been added. When the manual focus is set, the icons are displayed to indicate the focus state of the area you have touched.
- "2160/60p" (JUST) has been added to the system format.
- 4K color bar TYPE4/TYPE5 have been added to "COLOR BAR TYPE" • TYPE4: ARIB (UHD) • TYPE5: ARIB (2020/HLG)
- "Down conversion from UHD to FHD" has been added to NDI (High bandwidth NDI) output format.
- IP distribution can be used when the system frequency is 60Hz (JUST).
- "Fixed IP address" has added for [USB] setting. "DHCP" or "Fixed IP" can be selected like as [LAN] and [SFP+].
- WEB screen status display has been added. ST2110 RX (RETURN) format information (Format/Framerate), G/L sync information display.
- A selection item of REF SIGNAL has been renamed. Related menu: BASIC CONFIG - SYNC SIGNAL - REF SIGNAL The selection item "SDI" has been changed to "BBS/TRI-LEVEL SYNC"
- A new Digest authentication mode has been added "Wait time mode". When using a Panasonic controller (AW-RP150, AW-RP60), set [Wait time mode] to [Mode2] when using digest authentication.
[Mode1] (Initial value) This is the setting recommended if security is to be prioritized.
[Mode2] The wait time for re-entry is shorter. This is the setting recommended if operability is to be prioritized.
- The following items in PICTURE - IRIS have been added to the backup target of the SCENE file. AUTO IRIS, WINDOW SELECT, PICTURE LEVEL, PEAK RATIO, AUTO IRIS CLOSE LIMIT, IRIS SPEED
- If you want to update so that the IRIS setting value is not initialized before and after the update, save the SCENE file by either method (2) or (3). In method (1), each item of IRIS is initialized.
(1) Load the SCENE file (OSD menu: FILE - SCENE FILE) that was saved with the camera before the update with the camera after the update.
(2) Download a SCENE file to the camera before the update. (Web screen: Maintenance - Backup) Upload the SCENE file to the camera after the update.
(3) Store a SCENE file on the SD card of our controller (RP150/RP60) before the update. (Controller side menu: MAINTENANCE - FILES) Load the SCENE file with the camera after the update.
- When using the FP+ terminal, H.264/H.265 UHD/75Mbps distribution and HTTP communication (access to web screens, etc.) cannot be performed.
- PTP synchronization function has been improved to operate without delay according to PTP domain settings.
- Operational stability has been improved under special conditions. (Continuous switching between power ON/OFF, Format, 50Hz/59.94Hz, etc.)
- Values over 50000 can be set correctly for Destination port of ST2110.
Updating to a newer firmware version than the one already installed on your network camera can improve the device's overall performance and stability, resolve various issues, and add support for newly developed features or enhance existing ones.
On the other hand, downgrading the camera's firmware can recover its functionality in the unlikely event the currently installed version is faulty, or the device's performance dropped after an upgrade. However, bear in mind that applying an earlier build might not always be possible.
Changing the camera's firmware must be performed when the new release resolves an issue that your device has encountered or adds a new feature (or enhances an existing one) that could prove useful to you.
As for the installation method, the steps vary depending on the model you own, but basically, you must connect your camera via an Ethernet cable (username and password required), and use the downloadable file in the Firmware Update section to upgrade your device. Make sure you do not interrupt the installation process.
However, make sure you carefully read and understand the installation steps so that you don't end up with a broken device. This process isn't intended to be destructive, but still, it's best to save all configurations before applying a different firmware.
That being said, if you consider that this firmware improves your device in any way, then hit the download button and get the desired version; if not, check our website as often as possible so that you don't miss the update that will boost your camera's performance.
Top 4 Download periodically updates information of Panasonic AW-UE160PJ Camera Firmware 1.27 full driver from the manufacturer, but some information may be slightly out-of-date.
Using warez version of Panasonic AW-UE160PJ Camera Firmware 1.27 driver is hazardous. Our driver download links are directly from our mirrors or publisher's website, Panasonic AW-UE160PJ Camera Firmware 1.27 torrent files or shared files from free file sharing and free upload services, including Rapidshare, HellShare, HotFile, FileServe, MegaUpload, YouSendIt, MailBigFile, DropSend, MediaMax, zUpload, MyOtherDrive, SendSpace, DepositFiles, Letitbit, LeapFile, DivShare or MediaFire, are not allowed!
It is not recommended to download drivers from illegal sites which distribute a keygens, key generators, pirate keys, serial numbers, warez full versions or cracks for Panasonic AW-UE160PJ Camera Firmware 1.27. These drivers might corrupt your computer installation or breach your privacy. A driver might contain a trojan horse opening a backdoor on your computer. Hackers can use this backdoor to take control of your computer, copy data from your computer or to use your computer to distribute viruses and spam to other people.
Download Now
Update All Drivers