1. Modified the Mode LED activity when it is long pressed (~3 sec.) to set the Auto White Balance and/or Auto Exposure lock to provide positive visual feedback when the lock is set. For the photo and video modes, setting the lock while the camera is in Standby condition will momentarily turn off the colored LED to confirm when the lock is set. It will stay off until you release the Mode button, then turn back on solid indicating it is still in a Standby condition. In the video modes, the lock can still be set with a long press of the Mode button while the camera is recording, but now the colored LED blinking (if it is configured to turn on while recording) will momentarily turn off to confirm when the lock is set. It will stay off until you release the Mode button, then it resumes blinking indicating it is still recording. The recording will continue during the lock setting process even when the LED turns off while setting the lock.
2. A bug fix for Photo Mode Auto WB lock that caused the RGB settings to shift to a different set of fixed values after the first WB-locked photo was shot. Now all photos will have the same correct RGB settings that were detected when the lock was set.
DO NOT PRESS ANY BUTTONS during the firmware update process.
There are two methods with which you can update the firmware.
Method 1 without pressing any buttons:
• Turn off the camera.
• Connect the camera to the computer and wait until the card is recognized as a Removable Drive.
• Copy the new firmware file into the camera's flash card root folder. All firmware files are
named FWTLCAM.BIN. The name must not be changed.
• Disconnect the camera from the computer and wait until it turns off.
• Wait until all the LEDs are turned off.
• Connect the camera to the PC. The blue LED will turn on for about 13 seconds and then begin
to flash. WAIT.
• After another 7 seconds the blue LED will turn off. WAIT.
• After a second or two the yellow LED will turn on. WAIT
• The firmware file will be automatically deleted.
• The camera will automatically be connected as a removable device.
• After about 4 seconds the process is complete and the yellow LED will turn off.
• The camera is now ready for use as a USB drive.
Method 2 by pressing the power button :
• Turn off the camera.
• Connect the camera to the computer and wait until the card is recognized as a Removable Drive.
• Copy the new firmware file into the camera's flash card root folder. All firmware files are
named FWTLCAM.BIN. The name must not be changed.
• Disconnect the camera from the computer and wait until it turns off.
• Wait until all the LEDs are turned off.
• Turn on the camera and WAIT.
• The blue LED will turn on for about 13 seconds and then begin to flash. WAIT.
• After another 7 seconds the blue LED will turn off. WAIT.
• After a second or two the yellow LED will turn on indicating the firmware file has been
automatically deleted.
• The camera is now in standby mode and ready for use.
Updating to a newer firmware version than the one already installed on your camera can improve the device’s overall performance and stability, resolve various issues, and add support for newly developed features or enhance existing ones.
On the other hand, downgrading the camera’s firmware can recover its functionality in the unlikely event the currently installed version is faulty or the device’s performance dropped after an upgrade. However, bear in mind that applying an earlier build might not always be possible.
It is recommended that changing the camera’s firmware be performed when the new release resolves an issue that your device has been encountering, or adds a new feature (or enhances an existing one) that could prove useful for you.
This process isn’t intended to be destructive, but still, it’s best to save all your personal data and configurations before applying a different firmware. Moreover, make sure that the battery is fully charged and don’t use the camera’s buttons while the installation is in progress.
When it comes to the update method, usually, you must copy the firmware file onto a compatible memory card, insert it into the camera, and browse from the menu to the device’s update section.
However, each device has various ways to enter the update mode and particular steps that should be taken for a successful upgrade, therefore make sure you read the product’s installation guide.
That being said, if you consider that this firmware improves your device in any way, then hit the download button and get the desired version; if not, check with our website as often as possible so that you don’t miss the update that will boost your camera’s performance.
Top 4 Download periodically updates information of Mobius ActionCam Firmware 2.33 full driver from the manufacturer, but some information may be slightly out-of-date.
Using warez version of Mobius ActionCam Firmware 2.33 driver is hazardous. Our driver download links are directly from our mirrors or publisher's website, Mobius ActionCam Firmware 2.33 torrent files or shared files from free file sharing and free upload services, including Rapidshare, HellShare, HotFile, FileServe, MegaUpload, YouSendIt, MailBigFile, DropSend, MediaMax, zUpload, MyOtherDrive, SendSpace, DepositFiles, Letitbit, LeapFile, DivShare or MediaFire, are not allowed!
It is not recommended to download drivers from illegal sites which distribute a keygens, key generators, pirate keys, serial numbers, warez full versions or cracks for Mobius ActionCam Firmware 2.33. These drivers might corrupt your computer installation or breach your privacy. A driver might contain a trojan horse opening a backdoor on your computer. Hackers can use this backdoor to take control of your computer, copy data from your computer or to use your computer to distribute viruses and spam to other people.
Download Now
Update All Drivers