MikroTik RouterOS SMIPS Firmware 7.1.4

What's new in 7.1.4:

- bgp - fixed VPNv4 route sending to remote peer;
- bridge - fixed destination NAT when using "use-ip-firewall" setting;
- bridge - fixed filter rules when using interface lists;
- bridge - fixed priority tagged frame forwarding when using "frame-types=admit-only-untagged-and-priority-tagged" setting;
- capsman - improved stability when running background scan on CAP;
- crs3xx - improved maximum allowed ACL rule calculation;
- crs3xx - improved system stability when creating many ACL rules on CRS317, CRS309, CRS312, CRS326-24S+2Q+ and CRS354 devices;
- l2tp - improved system stability when processing L2TP control messages;
- lte - made "no" the default value for "use-network-apn" parameter;
- lte - made "RG502QEAAAR11A06M4G" the last OTA firmware version update for Chateau 5G in RouterOS 7.1.x release tree;
- ntp - improved source address usage for reply packets;
- ospf - fixed default route origination when "default-originate=if-installed" "redistribute" is enabled;
- ospf - fixed incorrect LSA types when changing area types;
- ppp - added "comment" option for PPPoE servers;
- queue - improved system stability when using more than 255 unique packet marks;
- route - fixed ECMP load balancing in FastPath;
- route - fixed route addition to VRF from BGP;
- route - fixed routing configuration export on SMIPS devices;
- route-filters - renamed "-set" to "-list";
- sfp - improved SFP module detection on CRS106 and CRS112;
- switch - fixed port-isolation misconfiguration detection when using multiple switches;
- traffic-flow - do not handle NAT events when "nat-events" is disabled;
- ups - fixed UPS support;
- winbox - added "VPN" tab to "Routing/BGP" menu;
- winbox - added "VRF" parameter for "SSH" and "Telnet" menus;
- winbox - do not show "Antenna Scan" button on devices that do not support it;
- wireguard - allow same peer's public key for different interfaces;
- wireless - added "3gpp-info" parameter to interworking configuration;
- wireless - added EAP-AKA to interworking's realm configuration;
- wireless - fixed interface initialization on Metal 2SHPn;

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn't either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn't be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don't always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you're looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don't power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don't miss the update that will improve your device.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.