MikroTik RouterOS PPC Firmware 7.1.2

What's new in 7.1.2:

- bgp - fixed routing table and BGP configuration order in export;
- bluetooth - disable scanning by defau<
- chr - improved system stability when writing into memory;
- chr - temporarily suspended downgrade to RouterOS v6;
- console - updated copyright notice;
- dhcpv4-server - remove dynamic leases when server configuration is removed;
- hotspot - fixed web page loading using HTTPS;
- interface - fixed minor memory leak when interface or connected route is changed;
- lte - added MAC address and IPv6 LL address persistence after reboot on EG12 and EG18 modems;
- lte - added class based support for configless RNDIS LTE modems;
- lte - expose diagnostics channel for all modems;
- lte - fixed IPv6 address addition after startup on R11e-LTE6;
- lte - fixed packet forwarding on R11e-4G and R11e-LTE-US;
- lte - fixed support for Sierra MC7710;
- lte - improved stability on "+EGMR" response in MBIM mode;
- lte - properly recognize MBIM modem in USB port as LTE on Chateau 5G;
- ntp - allow adding duplicate server address if dynamic entry exists;
- ntp - fixed "use-local-clock" when enabling server;
- ntp - fixed multicast mode support;
- ntp - improved IPv6 address support;
- ospf - added "ptmp-broadcast" interface type (compatible with RouterOSv6 PTMP type);
- ospf - convert ospf "static" redistribute to "static,dhcp,modem,vpn" after update from RouterOS v6;
- ospf - fixed external LSA not updating after prefix netmask change;
- ppp - fixed AT+CPIN chat when SIM PIN is specified;
- qsfp - correctly display auto-negotiation status;
- queue - improved system stability when processing traffic;
- route - fixed "suppress-hw-offload" update;
- route - fixed router's LSA for PTP networks;
- route - show OSPF and RIP specific attributes in "/routing route" table;
- route-filter - fixed incorrect invert-match configuration upgrade from RouterOS v6;
- route-filter - fixed range conversion after update from RouterOS v6;
- rpki - made RPKI verify non-strict, introduces new state "unverified";
- rpki - show expire timer;
- socks - fixed SOCKS5 support;
- system - fixed license loss on some RB1100Dx4 and RB4011 devices;
- tr069-client - added support for wireless client uptime reporting;
- usb - fixed display of incorrect port count for USB serial ports;
- vlan - fixed improper VLAN priority addition for routed packets;
- webfig - do not show side menu if WebFig is disabled by skin;
- winbox - added "VRF" parameter to "IP/Services" menu;
- winbox - added MLAG support;
- winbox - added ZeroTier support;
- winbox - allow setting "Interface" parameter for 100G LED types;
- winbox - do not show "Antenna Scan" button on devices that do not support it;
- winbox - fixed "action" field in "IP/Web Proxy/Access" menu;
- winbox - fixed address list type parameters in "Routing" menu;
- winbox - made OSPF interface type names consistent between CLI and GUI;
- x86 - added support for Intel E810 NIC;
- x86 - made "no" the default value for "disable-running-check" ethernet parameter;
- x86 - properly distinguish multiple NICs that share the same PCI bus number;

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn't either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn't be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don't always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you're looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don't power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don't miss the update that will improve your device.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.