MikroTik RouterOS ARM64 Firmware 7.2.2

What's new in 7.2.2:

- bgp - added initial support for prefix limit;
- bgp - improved stability when editing BGP template;
- bonding - fixed LACP flapping for RB5009 and CCR2004-16G-2S+ devices;
- ccr - added visible "passthrough" flag for interfaces on CCR2004-1G-2XS-PCIe;
- ccr - usability and stability improvements for passthrough interfaces on CCR2004-1G-2XS-PCIe;
- cd-install - allow selecting on which drive to install RouterOS;
- conntrack - limited full Connection Tracking warning to 1 message per minute;
- crs3xx - fixed storm rate on 1Gbps interfaces for CRS354 devices;
- defconf - suggest user to set up new password;
- dhcpv4-server - fixed minor logging typo;
- fetch - improved full disk detection;
- filesystem - fixed possible boot failure on RB850Gx2 and RB1100AHx2;
- filesystem - improved long-term filesystem stability and data integrity;
- gps - fixed minor value unit typo;
- ipv6 - removed bogus commands from IPv6 neighbors menu;
- l3hw - improved offloading for directly connected hosts on CRS305, CRS326-24G-2S+, CRS328, CRS318, CRS310;
- l3hw - improved route table offloading for CRS317, CRS309, CRS312, CRS326-24S+2Q+, CRS354, CRS5xx, CCR2x16 devices;
- leds - fixed ethernet LED behavior on wAP R ac;
- leds - fixed wireless related LED behavior with WW2 package;
- lte - added SMS sending support for MBIM protocol;
- lte - added support for generic PXA1802 based modems;
- lte - disabled wait for LTE auto attach;
- lte - hide slave interfaces from export;
- lte - improved stability when upgrading LTE firmware on Chateau 5G;
- mlag - fixed MAC address moving between bridge ports;
- mpls - do MPLS forwarding for nexthops without mappings;
- mpls - fixed MPLS MTU and path MTU selection;
- mpls - fixed MPLS forwarding after any interface configuration parameter is changed;
- ospf - fixed GRE interface compatibility with OSPF;
- ospf - improved stability when enabling or removing interface-template entries;
- ovpn - fixed memory leak on TILE architecture;
- ovpn - fixed packet processing on MT7621A;
- ovpn - improved Windows client disconnect procedure in UDP mode;
- ovpn - improved service stability when processing frequent disconnects in UDP mode;
- ovpn - improved stability when forwarding traffic on TILE;
- ping - fixed socket allocation after VRF change;
- ppp - fixed "remote-ipv6-prefix" parameter unsetting;
- ppp - fixed active sessions sometimes getting stuck;
- ppp - fixed issue with multiple active sessions when "only-one" is enabled;
- queues - improved stability in large list of queue scenarios;
- rb5009 - fixed 10G linking issues with Intel X520, XXV710 NICs;
- route - fixed "table" menu emptying after RouterOS upgrade;
- route - fixed static routes in VRF becoming invalid after reboot;
- route-filter - fixed community matchers;
- rsvp-te - improved stability when "Resv" received for non-existing session;
- supout - added RIP section;
- system - fixed IP service initialization in VRF after system startup;
- system - fixed rare partial loss of RouterOS configuration after package upgrade/downgrade/install/uninstall;
- torch - properly capture all related IPv6 traffic;
- upnp - improved stability when processing incomplete HTTP header;
- vpls - fixed "pw-l2mtu" parameter usage;
- vrf - fixed VRF leaking;
- winbox - do not show "unknown" area under "Routing/OSPF/LSA" menu;
- winbox - do not show type value for NXDOMAIN entries under "IP/DNS/Cache" menu;
- winbox - made "Interface Templates" table sortable under "Routing/OSPF" menu;
- winbox - properly clean up SFP module information after it is unplugged;
- winbox - properly clean up disk after a failed file upload;
- winbox - show PVID column by default under "Bridge" menu;
- wireless - fixed EAP-TLS authentication;
- wireless - fixed GUD version in 3gpp information;
- ww2 - fixed VLAN tag handling;
- x86 - improved support for i40e driver;
- x86 - improved support for Intel E810 NIC;

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn't either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn't be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don't always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you're looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don't power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don't miss the update that will improve your device.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.