MikroTik RouterOS ARM Firmware 7.10 Beta 8

Changes in this release:

- ipv6 - fixed DNS server processing by IPv6/ND services (CVE-2023-32154);
- route - added BFD (CLI only);
- bgp - allow to filter BGP sessions by AFI;
- bgp - changed default VPNv4 import distance to iBGP value (200);
- bgp - do not check route distinguisher on import;
- bgp - fixed "as-override" and rename to "output.as-override";
- bgp - fixed "remove-private-as" and rename to "output.remove-private.as";
- bgp - show address family in advertisements;
- bgp - show approximate received prefix count by the session;
- branding - fixed custom logo (introduced in v7.8);
- conntrack - added read-only "active-ipv4" and "active-ipv6" fields to "/ip/firewall/connection/tracking" (CLI only);
- console - fixed "print without-paging" output in some cases;
- defconf - allow to use device factory preset credentials in Flashfig and Netinstall configuration files;
- dhcpv4-server - added name for "IPv6-Only Preferred" option (108) in debug logs;
- doh - less verbose logging;
- ipsec - added hardware acceleration support for IPQ-5010 (hAP ax lite);
- ipsec - removed "ec2n185" and "ec2n155" values from proposal configurations;
- l3hw - added "autorestart" option to L3HW settings;
- l3hw - added error message and reset "l3-hw-offloading=no" if L3HW driver fails to start;
- l3hw - fixed offloading of /32 IPv4 and /128 IPv6 routes;
- l3hw - improved offloading of IPv6 hosts after L3HW driver restart;
- l3hw - improved performance of partial offloading;
- l3hw - improved route offloading after gateway change;
- lora - improved gateway card detection and upgrade logic;
- lora - updated firmware version for LoRaWAN gateway (for R11e-LoRa8, R11e-LoRa9 cards);
- lte - fixed APN authentication for R11e-LTE6 modem;
- lte - improved MBIM modem firmware reported error handling when settings RAT modes;
- lte - improved modem firmware upgrade stability for MBIM modems;
- lte - reduced SIM slot switchover time for MBIM modems with UUIC reset support;
- netwatch - added warning about non-running probe due to "startup-delay" (CLI only);
- poe - fixed bogous "poe-in-voltage" values when using DC jack for RB5009;
- qos-hw - renamed VLAN "priority" field to "pcp" to avoid confusion;
- rose-storage - added support for multiple smb users and smb shares;
- routerboot - increased "preboot-etherboot" maximum value to 30 seconds ("/system routerboard upgrade" required);
- scheduler - fixed incorrectly started scheduler during reboot or shutdown;
- sfp - fixed combo-sfp linking at 1G rate for CRS312 switch;
- sfp - improved module compatibility with bad EEPROM data for RB4011, RB5009, CCR2xxx, CRS312 and CRS518 devices;
- sniffer - fixed large .pcap file limit;
- snmp - added BGP peer table support IPv4 only (1.3.6.1.2.1.15.3.1);
- tr069 - added 5G SCC "SNR" parameter for modems that report it;
- vrrp - added warning if "sync-connection-tracking=yes" while the global connection tracking is inactive;
- vrrp - added warning if the VRRP group is misconfigured;
- vrrp - added warning if VRRP or its interface does not have an IP address;
- vrrp - do not start connection synchronization if the global connection tracking is inactive;
- vrrp - fixed issue where disabled VRRP interface is affecting group;
- vrrp - fixed VRRP interface state on physical cable disconnection;
- vrrp - improved system stability on changing "group-authority" or "sync-connection-tracking";
- vrrp - renamed "group-master" to "group-authority" to avoid confusion with VRRP master;
- vrrp - send VRRP announcements only by "group-authority";
- wifiwave2 - do not include in radio hardware capability list a parameter irrelevant to end users (introduced in 7.10beta5);
- wifiwave2 - fixed CAP interface name when using "name-format";
- wifiwave2 - fixed connectivity issues wheen access-list is used;
- wifiwave2 - fixed wireless throughput issues after 802.11r client roaming events on 802.11ac devices;
- wifiwave2 - improve protections against DoS attacks on WPA3-PSK;
- wifiwave2 - less verbose logging when WPA3-PSK clients are connecting;
- wireguard - retry "endpoint-address" DNS query on failed resolve;

Other changes since v7.9:

- bridge - fixed HW offloaded STP state on port disable;
- bridge - fixed HW offloading for vlan-filtered bridge on devices with multiple switches (introduced in v7.8);
- certificate - fixed displaying of certificate serial number;
- certificate - improved error reporting for Let's Encrypt certificate;
- certificate - restore available "key-usage" property options;
- console - added timeout error for configuration export;
- console - changed time format according to ISO standard;
- console - disable output when using "as-value" parameter;
- console - fixed ":terminal inkey" input when resizing terminal;
- console - hide past commands with sensitive arguments;
- container - fixed "container pull" to support OCI manifest format;
- container - fixed crash due to missing system directories;
- container - improved default internal environment values;
- defconf - fixed default configuration for RBSXTLTE3-7;
- dhcp-server - fixed accounting on RADIUS interim update;
- firewall - added "endpoint-independent-nat" support;
- firewall - added "nth" option for IPv6 firewall;
- gps - expose GPS port for Quectel RM520N-GL;
- ike2 - improved child SA delete request processing;
- iot - added option to send Modbus function code commands directly from RouterOS (CLI only);
- ipsec - refactor public key authentication;
- ipv6 - fixed IPv6 address removal;
- l3hw - added advanced configuration options for fine-tuning the L3HW offload (l3hw-settings are cleared after upgrade or downgrade) (CLI only);
- l3hw - added monitoring options for L3HW utilization (CLI only);
- l3hw - fixed /32 route deletion;
- l3hw - improved system stability for partial routing table offload;
- lte - added serving cell query for MBIM modems with necessary MBIM extension;
- lte - disable DHCP request filtering (UDP port 67) for Chateau 5G;
- lte - fixed Google Pixel 7 tethering support;
- lte - improved stability for Chateau 5G LTE modem firmware upgrade;
- lte - stop "cell-monitor" on LTE interface configuration change for MBIM modems;
- mpls - added FastPath support;
- ovpn - added initial support for V2 data transfer protocol;
- ovpn - improved system stability;
- pppoe - fixed PPPoE client scan when server is sending PADO messages without Service-Name tag;
- qos-hw - added QoS marking support for 98DXxxxx switches (CLI only);
- route - improved system stability when removing multicast forwarding entries;
- routerboard - fixed memory test on CCR2116-12G-4S+ ("/system routerboard upgrade" required);
- routerboard - improved RouterBOOT stability for Alpine CPUs ("/system routerboard upgrade" required);
- sfp - fixed combo-ether link monitor for CRS328-4C-20S-4S+ switch;
- sfp - improved Q/SFP interface stability for 98DX8208, 98DX8212, 98DX8332, 98DX3257, 98DX4310, 98DX8525, 98DX3255, 98PX1012 switches;
- sfp - improved SFP interface handling for RB4011, RB5009, CCR2xxx and CRS518 devices;
- sfp - improved system stability with certain SFP modules for CCR2216 and CRS518 devices;
- sfp - report EEPROM data even if "auto-init-failed" has occurred;
- smb - improved SMB v1 operation;
- snmp - added "engine-id-suffix" setting and display actual "engine-id" as read-only property;
- snmp - added new "mtxrInterfaceStatsTxRx1024ToMax" OID to MIKROTIK-MIB;
- ssh - added inline key "passphrase" property;
- switch - added more precise "storm-rate" configuration options for 98DXxxxx switches (CLI only);
- switch - fixed storm rate on 10G links for 98DX8208, 98DX8216, 98DX8212, 98DX8332, 98DX3257, 98DX4310, 98DX8525, 98DX3255 switches;
- system - improved watchdog reporting in log after reboots for several ARM and ARM64 devices;
- tile - fixed support for microSD card;
- upgrade - do not run manual upgrade if some packages are missing;
- ups - fixed updating of "battery-voltage" property;
- w60g - improved interface stability for PTMP setups;
- webfig - added high-resolution favicon;
- webfig - allow limitless upper bounds for number range;
- webfig - allow to set "0" second time for fields with default values;
- webfig - changed time format according to ISO standard;
- webfig - display date and time in local time zone;
- webfig - fixed missing "WifiWave2" menu;
- webfig - fixed missing property names in "WifiWave2" menu;
- webfig - redesigned item configuration display;
- webfig - redesigned top menu bar;
- webfig - removed "Tools/Telnet" menu;
- webfig - removed auto-login with default credentials (admin without a password);
- wifiwave2 - avoid transmitting extra bytes at the end of the packet after stripping a VLAN tag;
- wifiwave2 - do not show placeholder transmit power values on interface startup;
- wifiwave2 - fixed CAP connection when provisioning "manager=capsman";
- wifiwave2 - fixed DFS channel availability warning (introduced in v7.9);
- wifiwave2 - fixed dynamic interface adding to bridge on CAP device;
- wifiwave2 - fixed inability to disable CAPsMAN when there are RADIUS-authenticated clients connected;
- wifiwave2 - fixed incorrect limits on number of interfaces in station mode;
- wifiwave2 - fixed interface name change when restoring backup;
- wifiwave2 - fixed key handshake timeout with re-associating clients;
- wifiwave2 - fixed OWE authentication compatibility with 802.11ax client devices;
- wifiwave2 - fixed OWE authentication compatibility with third-party client devices (introduced in v7.8);
- wifiwave2 - improved logging when an interface is unable to assign a VLAN tag to client;
- wifiwave2 - improved system stability when trying to exceed virtual AP limit;
- wifiwave2 - improved system stability;
- wifiwave2 - restore interface running state when connection to CAPsMAN is lost;
- winbox - added "Queues" configuration tab when creating new entries under "IPv6/DHCP-Server" menu;
- winbox - rename "URL" property to "Action data" under "IP/Web-Proxy/Access" menu;
- wireguard - fixed IPv6 traffic processing with multiple peers;
- x86 - ice driver update to v1.11.14;
- zerotier - make "identity" setting sensitive;

About Router Firmware:

Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn't either newer or matching this release.

Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.

In theory, these steps shouldn't be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don't always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.

If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.

If you're looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don't power off the router or use its buttons during the installation, if you wish avoid any malfunctions.

If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don't miss the update that will improve your device.