- System BIOS: R01.01.0006 or later
- ME Firmware: 04.04.04.202
- BMC Firmware: 2.89.7e3b728b
- FRUSDR: 0.42
- CPLDL: v3P9
- Pmem: 2.2.0.1553
- System BIOS: R01.01.0007
- ME Firmware: 04.04.04.202
- BMC Firmware: 2.90.e5e4d391
- FRUSDR: 0.44
- Pmem: 2.2.0.1553
- CPLD: v4P2
- sysfwupdt.efi - Version 16.0.7
- Add enabling check on sensor scan thread to avoid dead lock. (Part 2) (#569)
- Add delay/lock for FRU and PSUFRU thread (#582)
- Off by one out of bounds write in PSWriteBlockReadData (#583)
- Retry to read RSSD status in AMP (#572)
- Fix CVE-2022-3435 (#576)
- Add SDR version in BMC debug log. (#574)
- Add enabling check on sensor scan thread to avoid dead lock. (#560)
- Avoid overflow in AgentSMBIOS_SendDataBlock (#556)
- Check Group ID range before it is used.
- Use memcpy_s to avoid overflow of cmd.Target.
- Avoid overflow in the request AgentSMBIOS_DataStart (#550)
- The klockwork issue on Libs (#205)
- When create IVM of 150M and then upload a 30M file via redfish, it returns 500 error (#549)
- Check the zip file before doing the decompression (#541)
- Fix the info of "Reset Immediately" for BMC in EWS (#539)
- Expand the topmenu width of browser (#524)
- Fix the help info, replace the "System reset" to "BMC reset" in BMC help (#523)
- Fix the issue that "Invalid data format " message will pop-up when mounting a WebISO if host user contains digits. (#522)
- Cache riser FRU to show FRU data when riser EEPROM is busy. (#528)
- Request length may exceed max allowed read length
- Request length may exceed max cmd length
- Fix possible overflow of combined unsigned values.
- Fix changing the KVM Encryption value, then launch the KVM, the keyboard and mouse will be no response. (#500)
- Override biosID when new biosID is shorter than old one. (#517)
- Fix klocwork issue (#515)
- Fix klocwork issue(UNINIT.STACK.ARRAY.MIGHT) (#514)
- Change Error MSG when system ID is invalid
- RAID Service source code integration (#495)
- Fix the garbage characters in systemdebuglog smbios section (#492)
- Remove MTM2 restriction on delete cmd for pnv license file. (#487) (#511)
- Add ATS auto fan profile switch support for TNP (#501)
- Change the mctp_config, for reading NIC successed (#499)
- Fix the bug that enable host interface,channel-4 options cannot be found in EWS->IPv4 or IPv6 Network Settings. (#494)
- Map U2 SSD slot according to new HSBP FW (#493)
- Change BIOS ID to SE5C620.01.01.0007
- [HSD]:[2103655321] Update the string of AtomicOp Egress Blocked Mask
- [HSD]:[2103655907] Setup knobs default value were disabled using syscfg to check them
- [CCB]:[3717][HSD]:[15011976683] CCB3717 Enable MCA Recovery in Whitley DSG Commercial BIOS
- [HSD]:[15011975987] Set FALSE in Whitley Sustaining phase
- [HSD]:[15011741796] Add X2APIC call back function to auto enable VT-D when it is enabled.
- [HSD]:[15012111145] It will logging ECC event log at OS when Enable MCA Recovery.
- [HSD]:[15011849958] Enhance SMBIOS Type 9 System Slot Table for endpoint device enumeration.
- [BIOS Option Changed][CCB]:[3694][HSD]:[15011621856] Add Enable Custom Refresh Enable and Custom Refresh Rate BIOS setup knobs.
- Add Advanced->Memory Configuration->Custom Refresh Enable, default is Disabled
- Add Advanced->Memory Configuration->Custom Refresh Rate, default is 20 (need enable Custom Refresh Enable option first).
- [BIOS Option Changed][CCB]:[3695][HSD]:[15011623886] Expose 'Data Link Feature Exchange' in M50CYP/D50TNP BIOS SETUP Interface.
- Advanced->Integration IO Configuration->PCIe Misc. Configuration->Socket X Configuration->Port XX->Data Link Feature Exchange, default is Enabled
- [CCB]:[3673][HSD]:[15011621801] Add "PCIE Fatal error mask settings" to CYP/TNP BIOS ITK interface
- [CCB]:[3627][HSD]:[15011621760] Create new AXXTPMENC8+ parts for ROW based on Infineon 9672 to supersede current 9670 based parts
- [HSD]:[2103655182] Inject Uncorrectable Non Fatal error to DIMM Rank 1 via WHEAHCT command, the SEL log show Rank 0
- [HSD]:[2103654470] If admin password is set, flash BIOS with bin file isn't requested 'password ' parameter but flash .cap file is needed it.
- [HSD]:[2103652728] Fix ParseSetup.py build error.
- [HSD]:[2103654492] HII of Intel_M50CYP does not display option to select PD while creating VD
- [HSD]:[15011915010] Add NVRAM corrupted check and set hob data NULL_VARIABLE_EVENT
- [HSD]:[22014698846] When SMX is fused off then SINIT & BIOS ACMs SVNs should contain Reset Value in SE SVN MSR.
- [HSD]:[15011871101] Unable to set BIOS admin password and Bios user password in OS Level of D50TNP"
- [HSD]:[15011838454] When Enable Partial Mirror at OS, mirror related option need hidden in BIOS setup
- [HSD]:[15011765544] Sync RP SGX setup criteria and callback function.
- [HSD]:[15011588767] Need remove DFX related options from BIOS and ITK
- [HSD]:[22014878309] Update on CLTT MRC whitepaper
- [HSD]:[22014923207] Generated
- [HSD]:[22015124973] Block Decoder will not get mapped if DDR is mapped up to MMIOH"
- [HSD]:[14015886212] Remove page policy adaptive restriction.
- Server-RC-0.4.2.0021
- [Utility] Upgrade utility to 16.0.7
- Change sensor name of sensor 0x20 "ADDDC Error" -> "ADDDC VLS Event"
- [Utility] Upgrade utility to 16.0.6
1. Unzip the contents of the update package and copy all files to the root directory of a removable media (USB flash drive)
2. Insert the USB flash drive to any available USB port on the system to be updated
3. Power on the server and load the uEFI shell
4. Begin the update process running the Startup.nsh
5. Reboot the system after the update process has successfully completed
1. Unzip the package onto your system
2. Log into the BMC web GUI
3. Navigate to Configuration, then Firmware Update
4. Click browse, and direct the browser to the location of Purley_1.04.f80688d0.bin
5. Click upload. Progress and status will be shown as the update progresses
1. Unzip package and load onto a flash drive
2. Boot to UEFI shell, and navigate to the folder where this package lives
3. Run fwUpdateBMC.nsh and follow the prompts
01. After the final update has completed successfully, reboot the system
02. During POST, hit the
03. From the BIOS Setup Utility main menu, hit the
04. Hit the
04. At the main menu verify the BIOS revision is correct
05. Move cursor to the SERVER MANAGEMENT menu and hit Enter
06. Move cursor to the SYSTEM INFORMATION Option and hit Enter
07. Verify the BMC Firmware revision is correct
08. Verify the SDR revision is correct
09. Verify the ME Firmware revision is correct
10. Configure desired BIOS Option settings
11. Hit the F10 Key to Save Changes and Exit
Applying a newer firmware version than the one already installed on your unit can bring various enhancements, include workarounds for diverse problems encountered by the device, and improve or add newly developed features.
On the other hand, downgrading the firmware version can recover the device's functionality in the event of a software update either turning up faulty or causing the unit's overall performance to drop. However, bear in mind that applying an older firmware isn't recommended and might not always be possible.
When it comes to the update steps, due to the large variety of devices and numerous ways for installing a new firmware, it is recommended that you carefully read and understand the upgrade steps, and consider applying a different firmware only when you have familiarized yourself with the update method.
As the installation process is most of the times quite risky, this step should be taken by users that have the ability to successfully complete the update; regular users may initiate it at their own risk. Moreover, it's best that this task be performed in a steady power environment such as the one ensured by a UPS unit.
Therefore, if you consider applying this release, hit the download button, take into account all the aforementioned aspects, and update the device's firmware. Also make sure you constantly check with our website to ensure that you don't miss a single new release.
Top 4 Download periodically updates information of Intel D50TNP1MHCPAC Server System UEFI BIOS/Firmware 01.01.0007 full driver from the manufacturer, but some information may be slightly out-of-date.
Using warez version of Intel D50TNP1MHCPAC Server System UEFI BIOS/Firmware 01.01.0007 driver is hazardous. Our driver download links are directly from our mirrors or publisher's website, Intel D50TNP1MHCPAC Server System UEFI BIOS/Firmware 01.01.0007 torrent files or shared files from free file sharing and free upload services, including Rapidshare, HellShare, HotFile, FileServe, MegaUpload, YouSendIt, MailBigFile, DropSend, MediaMax, zUpload, MyOtherDrive, SendSpace, DepositFiles, Letitbit, LeapFile, DivShare or MediaFire, are not allowed!
It is not recommended to download drivers from illegal sites which distribute a keygens, key generators, pirate keys, serial numbers, warez full versions or cracks for Intel D50TNP1MHCPAC Server System UEFI BIOS/Firmware 01.01.0007. These drivers might corrupt your computer installation or breach your privacy. A driver might contain a trojan horse opening a backdoor on your computer. Hackers can use this backdoor to take control of your computer, copy data from your computer or to use your computer to distribute viruses and spam to other people.
Download Now
Update All Drivers