- This firmware adds the following function to complement the current support for still image shooting via USB communications:
a) and ending video recording
b) exposure settings (exposure mode, shutter speed, aperture, ISO sensitivity, exposure compensation) for video recording
c) Making manual focus adjustments for video recording
- This is the function via USB communication. About supported gimbals and drones, refer to support information not only on our website but also manufacturers’ websites.
- Improving the tracking performance of the eye AF frame, making it easier to attain accurate autofocus on the eyes.
- Improving face-detection performance when there are faces of different sizes within the same frame, making it easier to attain accurate autofocus.
- Improving autofocus capability on a foreground subject even when there is a mixture of foreground and background subjects within a AF frame, causing the foreground subject to go out of focus, e.g. when shooting flowers against a busy background.
- Until now, the number of pictures that can be saved in a folder on an SD card was limited to 999. This update will raise the limit by ten times to 9,999 pictures.
- Fix of minor defects.
- If firmware updating fails, the camera may no longer operate correctly in some cases.
- Always use the fully-charged battery when updating the firmware as a basic manner. Never turn the camera off or attempt to use any of the camera controls while the firmware is being overwritten.
- Firmware updating requires approximately 90 seconds.
- Once the firmware has been updated, some data of the previous version cannot be restored.
- Put the formatted memory card to a card reader slot of your PC / Mac.
- Download the firmware
- Copy the downloaded file to the card.
- Take the card from the card reader slot after the copy is completed and put it to the camera.
- Use a fully charged battery. If the camera turns off during the firmware update, it won't work well.
- The time for the firmware update varies depending on the capacity of the firmware, but it is approx. 90 sec. Never turn off the camera and operate it during the firmware update.
- Turn the camera on pressing "DISP/BACK" button to show the display in the right. Then, press the "MENU/OK" button
- After confirming the item as [BODY] to update the camera body, press [OK] button.
- Press the [OK] button to go to next step.
- Press the [UP button] to select "OK".
- Press the [OK] button.
- Firmware updating is started.
- It takes approximately 90 seconds for completing the firmware update.
- When this screen appears, the firmware update has been successfully completed.
- Turn the camera off.
- Check the upgraded firmware.
- By following the above procedure "Firmware version checking procedure", you can see the firmware version.
- Format the card.
Updating to a newer firmware version than the one already installed on your camera can improve the device's overall performance and stability, resolve various issues, and add support for newly developed features or enhance existing ones.
On the other hand, downgrading the camera's firmware can recover its functionality in the unlikely event the currently installed version is faulty or the device's performance dropped after an upgrade. However, bear in mind that applying an earlier build might not always be possible.
It is recommended that changing the camera's firmware be performed when the new release resolves an issue that your device has been encountering, or adds a new feature (or enhances an existing one) that could prove useful for you.
This process isn't intended to be destructive, but still, it's best to save all your personal data and configurations before applying a different firmware. Moreover, make sure that the battery is fully charged and don't use the camera's buttons while the installation is in progress.
When it comes to the update method, usually, you must copy the firmware file onto a compatible memory card, insert it into the camera, and browse from the menu to the device's update section.
However, each device has various ways to enter the update mode and particular steps that should be taken for a successful upgrade, therefore make sure you read the product's installation guide.
That being said, if you consider that this firmware improves your device in any way, then hit the download button and get the desired version; if not, check with our website as often as possible so that you don't miss the update that will boost your camera's performance.
It is highly recommended to always use the most recent driver version available.
Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.
Top 4 Download periodically updates information of Fujifilm X-T30 Camera Firmware 1.20 full driver from the manufacturer, but some information may be slightly out-of-date.
Using warez version of Fujifilm X-T30 Camera Firmware 1.20 driver is hazardous. Our driver download links are directly from our mirrors or publisher's website, Fujifilm X-T30 Camera Firmware 1.20 torrent files or shared files from free file sharing and free upload services, including Rapidshare, HellShare, HotFile, FileServe, MegaUpload, YouSendIt, MailBigFile, DropSend, MediaMax, zUpload, MyOtherDrive, SendSpace, DepositFiles, Letitbit, LeapFile, DivShare or MediaFire, are not allowed!
It is not recommended to download drivers from illegal sites which distribute a keygens, key generators, pirate keys, serial numbers, warez full versions or cracks for Fujifilm X-T30 Camera Firmware 1.20. These drivers might corrupt your computer installation or breach your privacy. A driver might contain a trojan horse opening a backdoor on your computer. Hackers can use this backdoor to take control of your computer, copy data from your computer or to use your computer to distribute viruses and spam to other people.
Download Now
Update All Drivers