Atomos Sumo Recorder Firmware 9.12

Quad ISO recording

- Access from the Input menu – select “4xISO” under SDI MULTI LINK
- Supported formats: 1080p23.98/24/25/29.97/50/ 59.94, 1080i50/59.94,
- All signals must be the same format and synced to a reference signal
- Only channel 1/2 of the embedded audio for each stream plus analog input will be recorded and monitored
- SDI input 1 is the master reference for timecode and trigger
- All ISO recordings will have the same timecode

Switched output

- In ISO Record mode, the Output SDI connection is a Switched output based on the Input selection in the Home Screen and in the Quad View mode. This Switched output can be used as a program output and recorded on an External Atomos Recorder/Monitor, or used a Switched streaming source.

Panasonic EVA1 5.7k Raw

- Frame rates supported: 23.98/24/25/29.97/30
- Recording is supported for ProRes RAW only

Automatic HDR configuration in playback

- When playing a movie recorded with AtomHDR monitoring enabled all HDR settings will be automatically restored to match the settings when recording was started
- Select the “Auto HDR” button to enable this feature

Monitor mode

- “Mon” button will display a 4 way split view when 4xISO input mode is enabled
- “Mon” button will display a monitoring interface for quick access to monitor features for all other video modes
- Use the home button to return to record view

Firmware Update Tutorial:

- Download and unzip the file.
- Copy the file onto a recommended, formatted driver, using the docking station included with your recorder.
- Insert the drive into the Atomos recorder while it’s off.
- Power up the Atomos recorder.
- The screen will show flashing lines of color. This is normal - DO NOT power off!
- Updating will take a few minutes.
- Once completed, the Atomos recorder will power down.
- Power up the Atomos recorder again.
- Check Menu > Product Info > AtomOS Version. This should match the version you have just downloaded.
- Enjoy your updated Atomos recorder !

Firmware Recovery Tutorial:

- Power down the Atomos recorder (Hold power button for 4 seconds).
- Hold down the power button for 10 seconds approximately.
- You will see the “Firmware Update Failed” screen.
- Insert your HDD / SSD.
- The install process will begin and the screen will show flashing lines of color. This is normal - DO NOT power off !
- Once completed, the Atomos recorder will power down.
- Enjoy your updated Atomos recorder !

About Video Recorder Adapter Updates:

Applying a new firmware package on your Video Recorder adapter should improve overall performance and stability, fix various issues encountered with the device, or add support for newly developed features.

The Video Recorder adapter should be carefully upgraded by a power user (that is to say, someone who has the know-how to successfully complete the process), but it can also be performed by an average user at his or her own risk.

Either way, given the fact that each producer has their own method for installing a new firmware, and that every device has a particular way to enter the update mode, you must not consider upgrading the adapter's software until you have read and thoroughly understood the installation steps.

As a rule, said steps shouldn't pose too much of a challenge because manufacturers strive to make them as easy as possible. As with everything else, exceptions do occur, and users should be prepared for them.

Usually, you should transfer the compatible firmware to the Recorder through a USB cable or a memory card, and afterwards enter update mode from the unit's setup menu or through a specific power-on method.

With this in mind, if you intend to apply this release, make sure the package is compatible with your Video Recorder and that it brings about the changes you want or require; hit the download button and apply the new firmware.

Don't forget to regularly check with our website so that you don't miss any updates.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.