- NOTE: RT-AX56U is exceptionally included in this release.
- NEW: Rewrote VPN killswitch implementation. The new method uses an always present routing rule to prohibit access to the main routing table, so it will be active even if the user manually stops a client. Removing the prohibit rule requires disabling the killswitch on the webui. The rules are also created before WAN goes up, to reduce the risks of leaks between WAN going up and VPN connecting. Make sure to double check that you don't have any unwanted killswitch enabled if you have connectivity issues following the upgrade to this firmware.
- NEW: Added killswitch support for WireGuard clients.
- NEW: Added mDNS support to the router's local name resolution (nss).
- UPDATED: Chart.js was upgraded from 2.x to 3.9, to share the same version used by Asus. Any third party addon that used it will need to upgrade their charts to the new version.
- UPDATED: wget to 1.24.5.
- CHANGED: Removed stop/start and "Start with WAN" buttons from OpenVPN clients. There is now just a single "Enable" option, which will immediately start the client when applying changes, and will also start it automatically when WAN comes up. This is to reduce confusion, better integrate into SDN, and match how WireGuard clients already worked.
- CHANGED: Allow text selection on the Wireguard Server settings page.
- FIXED: JS error on Wifi 6e/7 models when toggling DDNS.
- FIXED: Couldn't mount CIFS shares on the router for BCM4912 devices.
- FIXED: Wrong band shown when selecting the 5 GHz band on the WPS page for the GT-AXE11000.
- FIXED: WPS page wouldn't properly detect if 6 GHz radio is disabled when selecting it for the GT-AXE11000
- FIXED: Disabling IGDv2/pinhole support wasn't fully disabling IPv6 support.
- FIXED: CVE-2024-3080 issue
- REMOVED: Wifi Radar was removed (unsupported by Wifi 7 devices, and security issues cited by Asus in their own recent releases).
- Simply flash it like any regular update. You should not need to reset to factory defaults (see note below for exceptions). You can revert back to an original Asus firmware at any time just by flashing a firmware downloaded from Asus's website.
- If the firmware upgrade fails, try rebooting your router to free up sufficient memory, without any USB disk plugged in, then try flashing it again.
- If you run into any issue after an upgrade and you haven't done so,try doing a factory default reset as well.
- Always read the changelog, as mandatory resets will be mentionned there when they are necessary.
- In all of these cases, do NOT load a saved copy of your settings! This would be the same thing as NOT resetting at all, as you will simply re-enter any invalid setting you wanted to get rid of. Make sure to create a new backup of your settings after reconfiguring.
- Resetting to factory default after flashing is strongly recommended for the following cases: Updating from a firmware version that is more than 3 releases older or Switching from a Tomato/DD-WRT/OpenWRT firmware
- This custom firmware can be applied like any regular update.
- You should not need to reset to factory defaults.
- You can revert back to an original ASUS firmware at any time.
- Do not load a saved copy of your settings.
Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn't either newer or matching this release.
Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.
In theory, these steps shouldn't be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don't always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.
If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.
If you're looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don't power off the router or use its buttons during the installation, if you wish avoid any malfunctions.
If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don't miss the update that will improve your device.
Top 4 Download periodically updates information of ASUS RT-AX88U AsusWrt-Merlin Firmware 3004.388.8.0 full driver from the manufacturer, but some information may be slightly out-of-date.
Using warez version of ASUS RT-AX88U AsusWrt-Merlin Firmware 3004.388.8.0 driver is hazardous. Our driver download links are directly from our mirrors or publisher's website, ASUS RT-AX88U AsusWrt-Merlin Firmware 3004.388.8.0 torrent files or shared files from free file sharing and free upload services, including Rapidshare, HellShare, HotFile, FileServe, MegaUpload, YouSendIt, MailBigFile, DropSend, MediaMax, zUpload, MyOtherDrive, SendSpace, DepositFiles, Letitbit, LeapFile, DivShare or MediaFire, are not allowed!
It is not recommended to download drivers from illegal sites which distribute a keygens, key generators, pirate keys, serial numbers, warez full versions or cracks for ASUS RT-AX88U AsusWrt-Merlin Firmware 3004.388.8.0. These drivers might corrupt your computer installation or breach your privacy. A driver might contain a trojan horse opening a backdoor on your computer. Hackers can use this backdoor to take control of your computer, copy data from your computer or to use your computer to distribute viruses and spam to other people.
Download Now
Update All Drivers
