- NEW: IPV6 support for DNSFilter for HND router models. Custom settings can also let you specify IPv6 servers. These (as well as providers that support IPv6) will now also get intercepted and redirected like the IPv4 DNS servers are.
- UPDATED: Merged with 386_49335 GPL for the RT-AC5300.
- UPDATED: Merged with 386_48966 GPL for all other models.
- UPDATED: openssl to 1.1.1o.
- UPDATED: haveged to 1.9.18.
- UPDATED: openvpn to 2.5.7.
- UPDATED: tor to 0.4.7.8.
- CHANGED: dhcpc-event now has a second parameter that will contain "4" or "6" depending on the IP protocol of the event (dave14305)
- FIXED: JFFS backup/restore functions not working on XT12 and GT-AX6000.
- FIXED: CVE-2022-0934 in dnsmasq (backport)
- FIXED: CVE-2022-26376 (reported by Cisco Talos, fixed by Asus)
- FIXED: DNSFilter client list was limited to around 10 clients on some models.
- FIXED: AuraRGB could be re-enabled on reboot if it was previously disabled.
- FIXED: Wifi LEDs wouldn't turn back on when re-enabling LEDs on the RT-AX86S.
- Simply flash it like any regular update. You should not need to reset to factory defaults (see note below for exceptions). You can revert back to an original Asus firmware at any time just by flashing a firmware downloaded from Asus's website.
- If the firmware upgrade fails, try rebooting your router to free up sufficient memory, without any USB disk plugged in, then try flashing it again.
- If you run into any issue after an upgrade and you haven't done so,try doing a factory default reset as well.
- Always read the changelog, as mandatory resets will be mentionned there when they are necessary.
- In all of these cases, do NOT load a saved copy of your settings! This would be the same thing as NOT resetting at all, as you will simply re-enter any invalid setting you wanted to get rid of. Make sure to create a new backup of your settings after reconfiguring.
- Resetting to factory default after flashing is strongly recommended for the following cases: Updating from a firmware version that is more than 3 releases older or Switching from a Tomato/DD-WRT/OpenWRT firmware
- This custom firmware can be applied like any regular update.
- You should not need to reset to factory defaults.
- You can revert back to an original ASUS firmware at any time.
- Do not load a saved copy of your settings.
Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn't either newer or matching this release.
Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.
In theory, these steps shouldn't be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don't always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.
If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.
If you're looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don't power off the router or use its buttons during the installation, if you wish avoid any malfunctions.
If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don't miss the update that will improve your device.
It is highly recommended to always use the most recent driver version available.
Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.
Top 4 Download periodically updates information of ASUS RT-AC1900P AsusWrt-Merlin Firmware 386.7.0 full driver from the manufacturer, but some information may be slightly out-of-date.
Using warez version of ASUS RT-AC1900P AsusWrt-Merlin Firmware 386.7.0 driver is hazardous. Our driver download links are directly from our mirrors or publisher's website, ASUS RT-AC1900P AsusWrt-Merlin Firmware 386.7.0 torrent files or shared files from free file sharing and free upload services, including Rapidshare, HellShare, HotFile, FileServe, MegaUpload, YouSendIt, MailBigFile, DropSend, MediaMax, zUpload, MyOtherDrive, SendSpace, DepositFiles, Letitbit, LeapFile, DivShare or MediaFire, are not allowed!
It is not recommended to download drivers from illegal sites which distribute a keygens, key generators, pirate keys, serial numbers, warez full versions or cracks for ASUS RT-AC1900P AsusWrt-Merlin Firmware 386.7.0. These drivers might corrupt your computer installation or breach your privacy. A driver might contain a trojan horse opening a backdoor on your computer. Hackers can use this backdoor to take control of your computer, copy data from your computer or to use your computer to distribute viruses and spam to other people.
Download Now
Update All Drivers
