- NOTE: For developers, please note that the new default branch is now called "main" - it's what was previously the 3006.102 branch. The "master" branch has been renamed "master-old", and is no longer actively used. Due to how the 3006.102 branch diverged, it was easier to do it this way than to fold back 3006.102 on top of master.
- NEW: Completely redesigned System Log -> Connections page: You can now filter the list, You can set the page to auto-refresh itself, Public IP addresses can be looked up on WhatismyIPaddress.com, Local hostnames will be resolved and shown, Routed IPv6 connections will be shown
- UPDATED: Merged GPL 3006.102_37957 for Wifi 6 devices.
- UPDATED: Merged GPL 3006.102_38757 for WIfi 7 devices.
- UPDATED: dropbear to 2025.88.
- CHANGED: Replaced netstat-nat by a fork called netstat-nat-ng. This fork fixes a number of issues with IPv6 and field size.
- CHANGED: Updated Control-D DoT server entries (dave14305).
- CHANGED: Optimized performance when refreshing the Sysinfo page on a network with thousands of tracked connections.
- CHANGED: Modified the Quick Internet Setup wizard so not to attempt downloading firmware updates from Asus (which would fail anyway).
- FIXED: OpenVPN server set to "Internet only" would fail to block LAN access (invalid firewall rule from SDN was bypassing it).
- FIXED: DNSDirector "Router" mode would not always work properly with IPv6 (now uses REDIRECT instead of DNAT, which was backported from iptables 1.4.19).
- FIXED: DNSDirector would try to create iptables rules even when that SDN should not allow DNSDirector if it shares the main LAN interface. This could break DNSDirector on the main network.
- FIXED: Status frame missing from Network Map when accessing the router under certain hostnames.
- FIXED: Wireless Settings page failing to save on some models when in an AiMesh setup.
- Simply flash it like any regular update. You should not need to reset to factory defaults (see note below for exceptions). You can revert back to an original Asus firmware at any time just by flashing a firmware downloaded from Asus's website.
- If the firmware upgrade fails, try rebooting your router to free up sufficient memory, without any USB disk plugged in, then try flashing it again.
- If you run into any issue after an upgrade and you haven't done so,try doing a factory default reset as well.
- Always read the changelog, as mandatory resets will be mentionned there when they are necessary.
- In all of these cases, do NOT load a saved copy of your settings! This would be the same thing as NOT resetting at all, as you will simply re-enter any invalid setting you wanted to get rid of. Make sure to create a new backup of your settings after reconfiguring.
- Resetting to factory default after flashing is strongly recommended for the following cases: Updating from a firmware version that is more than 3 releases older or Switching from a Tomato/DD-WRT/OpenWRT firmware
- This custom firmware can be applied like any regular update.
- You should not need to reset to factory defaults.
- You can revert back to an original ASUS firmware at any time.
- Do not load a saved copy of your settings.
Before you consider downloading this firmware, go to the system information page of the router and make sure that the currently installed version isn't either newer or matching this release.
Due to the large variety of router models and different methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you apply the new firmware, even if you are a power user.
In theory, these steps shouldn't be much of a hassle for anyone, because manufacturers try to make them as easy as possible, even if they don't always succeed. Basically, you must upload the new firmware to the router through its administration page and allow it to upgrade.
If you install a new version, you can expect increased security levels, different vulnerability issues to be resolved, improved overall performance and transfer speeds, enhanced compatibility with other devices, added support for newly developed technologies, as well as several other changes.
If you're looking for certain safety measures, remember that it would be best if you perform the upload using an Ethernet cable rather than a wireless connection, which can be interrupted easily. Also, make sure you don't power off the router or use its buttons during the installation, if you wish avoid any malfunctions.
If this firmware meets your current needs, get the desired version and apply it to your router unit; if not, check with our website as often as possible so that you don't miss the update that will improve your device.
Top 4 Download periodically updates information of ASUS GT-AX11000 PRO AsusWrt-Merlin Firmware 3006.102.5.0 full driver from the manufacturer, but some information may be slightly out-of-date.
Using warez version of ASUS GT-AX11000 PRO AsusWrt-Merlin Firmware 3006.102.5.0 driver is hazardous. Our driver download links are directly from our mirrors or publisher's website, ASUS GT-AX11000 PRO AsusWrt-Merlin Firmware 3006.102.5.0 torrent files or shared files from free file sharing and free upload services, including Rapidshare, HellShare, HotFile, FileServe, MegaUpload, YouSendIt, MailBigFile, DropSend, MediaMax, zUpload, MyOtherDrive, SendSpace, DepositFiles, Letitbit, LeapFile, DivShare or MediaFire, are not allowed!
It is not recommended to download drivers from illegal sites which distribute a keygens, key generators, pirate keys, serial numbers, warez full versions or cracks for ASUS GT-AX11000 PRO AsusWrt-Merlin Firmware 3006.102.5.0. These drivers might corrupt your computer installation or breach your privacy. A driver might contain a trojan horse opening a backdoor on your computer. Hackers can use this backdoor to take control of your computer, copy data from your computer or to use your computer to distribute viruses and spam to other people.
Download Now
Update All Drivers
