AMD RAID Installer 2.20.19.037 for Windows 11

Release Highlights:

- Installer supports Window 10 and Window 11.
- New version (9.3.0.296) of AMD RAID driver and AMD RAIDxpert2 utility.

Package Contents:

- AMD RAID Driver: 9.3.0.296
- AMD RAIDXpert2 Utility: 9.3.0.296
- AMD-RAIDXpert2 User Guide: 3.12

Known Issues & Limitations:

- RAID driver does not support S0i3.
- Error 1720 observed on re-Installation of the latest package after uninstalling the latest package using silent uninstall command.
- Installer UI may appear in background when launched.
- Installer may take long time (~ 10 min) to complete RAID components installation on upgrade scenarios.
- Double clicking the installer EXE multiple times shows Error pop-up window.
- Installer UI screen disappears during installation on a remote system when user manually disconnects RDP session and re-connect back.
- Installer goes to minimized and hang state on remote system when user minimizes the RDP session to task bar during Installer NSIS extraction phase.

Supported Chipsets for NVMe/SATA RAID:

- AMD WRX80
- AMD TRX40
- AMD X399
- AMD X570
- AMD B550
- AMD A520
- AMD X470
- AMD B450
- AMD X370
- AMD B350
- AMD A320

Supported Processors for NVMe/SATA RAID:

- AMD Ryzen Threadripper PRO Processors
- 2nd/3rd Gen AMD Ryzen Threadripper Processors
- AMD Ryzen 5000 Series Desktop Processors 
- 2nd/3rd Gen AMD Ryzen Desktop Processors
- AMD Ryzen 3000G/4000G/5000G Series Desktop Processors with Radeon Graphics
- AMD Ryzen Mobile 3000U/C, 4000U/H, 5000U/H/HS Series Processors with Radeon Graphics

Procedure to install AMD RAID Software:

- Run the executable AMD_RAID_Software_.exe.
- Accept the EULA agreement and proceed with Installation.
- User can selectively install the required AMD RAID components listed. (Recommended to install all the components listed).
- Once the Installation is complete, system reboot is required for AMD RAID drivers to function properly.

Procedure to Uninstall AMD RAID Software:

- NOTE: RAID Drivers will never be uninstalled by AMD RAID Software Installer, since it is a Boot Critical driver, uninstallation can lead to system failure.
- Open Control Panel & Browse to Programs and Features.
- Check for AMD RAID Software. Select Uninstall.
- User can select or unselect the intended AMD RAID components to be uninstalled.

Procedure to install via Command prompt With GUI mode:

- Navigate to AMD_RAID_Software_.zip’ containing folder in cmd.exe and run AMD_RAID_Software.exe.
- Accept the EULA agreement and proceed with Installation.
- User can selectively install the required AMD RAID components listed. (Recommended to install all the components listed).
- Once the Installation is complete, system reboot is required for AMD RAID drivers to work properly.

Procedure to install via Command prompt Silent Mode Installation:

- Invoke command prompt in Admin mode and execute the applicable commands mentioned in Attended Installation/Un-attended Installation sections below.
- Once the Installation is complete, system reboot is required for AMD RAID drivers to work properly.

Procedure to install via Command prompt Attended Installation:

- START /WAIT "" /S

Procedure to install via Command prompt Un-attended Installation:

- Important Note: Before continuing with NVMe RAID driver installation, ensure that the NVMe mode is configured as RAID in your motherboard BIOS. You should also take a backup of the data on your NVMe drives before executing below command.
- Install RAID NVMe Drivers: START /WAIT "" /S /RAIDPROMPT="Y"
- Important Note: Before continuing with SATA RAID driver installation, ensure that the both the SATA Controllers are configured as RAID in your motherboard BIOS.
- Install RAID SATA Drivers: START /WAIT "" /S /RAIDPROMPT="N"

Silent Mode un-installation:

- NOTE: RAID Drivers will never be uninstalled by AMD_RAID_Software.exe, since it is a Boot Critical driver, uninstallation can lead to system failure.
- Invoke command prompt in Admin mode and execute below command.
- START /WAIT "" /S /EXPRESSUNINSTALL=1 

About SATA / AHCI / RAID Drivers:

When you install an operating system, SATA settings (be it AHCI, RAID, or IDE mode) are detected from the BIOS. If you want to change from one mode to another after the OS has been applied, appropriate drivers are required.

Bear in mind that if you modify these settings without installing proper files first, the operating system will not be able to boot until changes are reverted or required drivers are applied.

To perform the latter task, get the package, run the available setup and follow the instructions displayed on-screen for a complete installation. Afterwards, perform a system reboot so that all changes take effect, enter BIOS menu, and set the SATA option to the mode that best describes the newly applied drivers.

So, if you intend to modify the SATA settings to the mode described by this release, click the download button, and make the desired changes. In addition to that, don't forget to constantly check with our website so that you don't miss a single new release.

  It is highly recommended to always use the most recent driver version available.

Try to set a system restore point before installing a device driver. This will help if you installed an incorrect or mismatched driver. Problems can arise when your hardware device is too old or not supported any longer.